by Abigail | Feb 28, 2022
OPA has not been evaluated by Clinical Consultants of DENTAL ADVISOR. It was chosen as a Clinical Problem Solver by consensus of the Editors.
Problem
Dental Practitioners have a difficult time prescribing night guards that have limited coverage by insurance companies. Many patients continue to experience symptoms of clenching and grinding, which require a lifetime management of pain, as well as protection against cracked teeth.
Solution
The OPA device, when used in conjunction with a therapeutic exercise program via My Mouth Works program, reinforces correct habits, promotes proper tongue placement and allows for jaw relaxation to maximize program efficiency. It is an all-in-one removable, adaptable nighttime appliance. The OPA helps eliminate maladaptive myofunctional habits that can damage hard and soft tissues. It is compatible to use over brackets, with clear aligners, and retainers. It can also be worn over dentures and partials. Depending on the oral condition, exercise programs can last approximately 8 to 16 weeks, all prescribed via a mobile app with reports are generated for both the patient and clinician to monitor and discuss progress.
Note: The OPA device may be used alone or in conjunction with the My Mouth Works program. Alone it is a FDA cleared device to promote a correct tongue position, protect the teeth and promote nasal breathing.
by Dental Advisor | Jan 11, 2022
Consultants’ Comments
- “The mask was very comfortable for our patients. They loved it. It fit well and didn’t pinch or leave any marks on the patient’s face.”
- “Easy to assemble and use.”
- “The mask is lightweight, low profile and small – the tubing is also lightweight.”
- “I’m able to do dentistry unimpeded using this system.”
- “I liked the ability to see through the mask.”
- “We found that the system was effective in delivering nitrous oxide and oxygen.”
- “I liked the scented masks. Patients didn’t complain about a plastic/rubber smell.”
Clinical Tips
- Size selection is very important – go down in size.
- Stretch the mask laterally when placing it and make sure the hose goes behind the ears.
- Let tubing dry for 5 hours after sterilization before use or it will be tacky and sticky.
- Turn the vacuum hose to the lowest power – the tight fit allows the evacuation of
- too much nitrous if you do not adjust the scavenging unit down.
- When using CSR-wrapping the tubing for sterilization, make sure there are no kinks in it.
Evaluation Highlights
Axess Low Profile Nasal Mask System was evaluated by 33 consultants, and was used 405 times in total.
- Soft, pliable and low profile translucent and clear single-use masks.
- Masks available in unscented, bubble-gum and mint scents.
- Lightweight, autoclavable tubing.
- Provides for good access to the clinical site.
Special Features
- Slim, low profile mask allows good visibility and access to the clinical site.
- Slender, lightweight scavenging circuit tubing to maximize accessibility to the oral cavity.
- Translucent and clear masks show the patient breathing – the masks fog up on exhalation.
- Comfortable for patients.
Indication
- Use when nitrous oxide/oxygen sedation is required.
Description
Axess™ Low Profile Nasal Mask System is used to deliver nitrous oxide/oxygen and to remove excess and exhausted gases. It consists of single-use, disposable nasal masks and reusable scavenging circuit tubing. The masks are small, low profile, latex-free and pliable for stability, complete access to oral cavity and to minimize ambient nitrous oxide and gas leakage from the mask. Masks are available in packs of 24 in either small, medium or large and for each size either as unscented (clear), bubble-gum scented (pink) or mint-scented (green) masks. Axess Scavenging Circuits are also latex-free and suitable for Crosstex/Accutron’s RFS Remote Flow System and In-Line/Accu-Vac vacuum controllers. The slender tubing wraps behind the patient’s ears and is secured by a slider under the chin. They are available in single packs with 6-foot long tubing, a complimentary selection of masks, a small gas connector, and various scavenging system adapters. Crosstex and Accutron are now proud members of HuFriedyGroup.
by Dental Advisor | Dec 20, 2021
Overview
- 43 Clinical Evaluators
- 2,276 Total Uses
- 96% Clinical Rating
Evaluators’ Comments
- “I liked the softness of my hands after using.”
- “ I have hardly had to use lotion since trying out the foam.”
- “No smell and no stickiness after using.”
- “Dries quickly and my hands felt clean after using.”
- “Usually, my hands get overdried and red after using sanitizers but this product was great.”
- “Noticeable alcohol odor at first that dissipates.”
- “It left my hands feeling dry and a bit of a film-like feeling.”
- “It evaporates quickly and really moisturizes.”
Indication
- Hand disinfection in the healthcare setting
Description
PURELL Advanced Hand Sanitizer ULTRA NOURISHING™ Luxurious Foam:
- Kills 99.99% of most common germs that may cause illness in as little as 15 seconds
- Evaporates quickly
- Leaves hands feeling clean
- Compatible with CHG as well as nitrile, latex, and vinyl gloves
- Dermatologist tested – hypoallergenic
Unique Attributes
- Improves and nourishes the skin’s natural moisture barrier*
- Improves skin hydration in three days (based on 100 uses per day)*
- Helps eliminate the need for lotion
- Recommended for frequent and repeated use
*Skin health study, Study # 2014-12-C10408, December 8-22, 2014, North Cliff Consultants, Inc., Cincinnati, OH.
For more information: PURELL Advanced Hand Sanitizer ULTRA NOURISHING Luxurious Foam
by Abigail | Nov 9, 2021
Amber Mill is the first machinable dental glass-ceramic blocks made of lithium disilicate. Its reinforced mechanical properties and aesthetic values with qualified machinability are greatly advantageous for patients and clinics. Denser and more crosslinked crystal structure of Amber Mill results in superior physical properties. Biaxial flexure strength of Amber Mill is about 10% higher than comparative product after it is fully crystallized. Outstanding machinability of Amber® Mill is evidently affirmative when checking the edges of the milled restorations. Highly stable edges with less chipping occurrence prove that Amber Mill is the best machinable lithium disilicate block for CAD/CAM system.
